Machine Tonnage Optimization by Reused Scrap Material Applied for Car Propeller Shaft Guard
作者： Lydia Anggraini , Ventika Aurora Pratiwi
DOI: 10.1109/ICSECC.2019.8907150
关键词:
摘要: The purpose of this research is to analyze how the scrap material or metal can be reused as a regular in production process. prepared use propeller shaft guard production. This used with main function car. Therefore, calculating total mass and needed know ratio usage material, machine tonnage calculation for using new design blanking material. producing 260.09 T. fit created. increased from 49.46% 79.69% after was comparison between condition before indicates factors amount dies, dandori are described research.
sci-hub.se 参考文章(17)
Albert Junaedi Gani, Liem Yenny Bendatu, Perbaikan Proses Dandori di PT. Astra Otoparts Tbk. Divisi Adiwira Plastik Jurnal Titra. ,vol. 3, pp. 1- 8 ,(2015)
Yasuo Yamane, Propeller shaft for vehicle ,(1996)
Peter B. Evans, Dependent Development: The Alliance of Multinational, State, and Local Capital in Brazil ,(1979)
Raffaele Cremiato, Maria Laura Mastellone, Carla Tagliaferri, Lucio Zaccariello, Paola Lettieri, Environmental impact of municipal solid waste management using Life Cycle Assessment: The effect of anaerobic digestion, materials recovery and secondary fuels production Renewable Energy. ,vol. 124, pp. 180- 188 ,(2017) , 10.1016/J.RENENE.2017.06.033
Rini Alfatiyah, ANALISIS MANAJEMEN RISIKO KESELAMATAN DAN KESEHATAN KERJA DENGAN MENGGUNAKAN METODE HIRARC PADA PEKERJAAN SEKSI CASTING SINTEK JURNAL: Jurnal Ilmiah Teknik Mesin. ,vol. 11, pp. 88- 101 ,(2017)
Sermpong Niemsakul, Nuttakorn Sae-Eawa, Yingyot Aue-U-Lan, Determination and analysis of critical damage criteria for predicting fracture in forming process by uniaxial tensile test Materials Today: Proceedings. ,vol. 5, pp. 9642- 9650 ,(2018) , 10.1016/J.MATPR.2017.10.152
Rahmat Nurcahyo, Saripuji Pustiwari, Djoko Sihono Gabriel, Developing a strategy map based on sustainability balanced scorecard framework for manufacturing industry in Indonesia International journal of engineering and technology. ,vol. 7, pp. 48- 51 ,(2018) , 10.14419/IJET.V7I2.34.13910
R S Rachmat, M Ogawa, Influence of Steel Strip Temperature in Formation Zinc Dross During Process Production Using Continuous Galvanizing Line (CGL) Machine IOP Conference Series: Materials Science and Engineering. ,vol. 395, pp. 012006- ,(2018) , 10.1088/1757-899X/395/1/012006
Ming Fan Qi, Yong Lin Kang, Quan Quan Qiu, Industrialized Application of Rheo-HPDC Process for the Production of Large Thin-Walled Aluminum Alloy Parts Solid State Phenomena. ,vol. 285, pp. 453- 458 ,(2019) , 10.4028/WWW.SCIENTIFIC.NET/SSP.285.453
Philippa Maia Horton, Julian M. Allwood, Christopher Cleaver, Implementing material efficiency in practice: A case study to improve the material utilisation of automotive sheet metal components Resources Conservation and Recycling. ,vol. 145, pp. 49- 66 ,(2019) , 10.1016/J.RESCONREC.2019.02.012