On the machinability of die/mold D2 steel material
作者： A. Hosseini , H. M. Hussein , H. A. Kishawy
DOI: 10.1007/S00170-015-7971-8
关键词:
摘要: The presented paper experimentally studies the machining of American Iron and Steel Institute (AISI) D2 steel as a frequently used material in die mold making industry. Several experimentations have been carried out using different cutting conditions such feed rate, depth cut, time. consequent effects these parameters on tool workpiece terms wear, forces power, surface integrity (surface roughness) recorded to investigate machinability material. results mainly reveal that time are most dominant play an important role characteristics steels.
springer.com
sci-hub.se 参考文章(19)
H. A. Kishawy, AN EXPERIMENTAL EVALUATION OF CUTTING TEMPERATURES DURING HIGH SPEED MACHINING OF HARDENED D2 TOOL STEEL Machining Science and Technology. ,vol. 6, pp. 67- 79 ,(2002) , 10.1081/MST-120003186
Helen Coldwell, Richard Woods, Martin Paul, Philip Koshy, Richard Dewes, David Aspinwall, Rapid machining of hardened AISI H13 and D2 moulds, dies and press tools Journal of Materials Processing Technology. ,vol. 135, pp. 301- 311 ,(2003) , 10.1016/S0924-0136(02)00861-0
V.N. Gaitonde, S.R. Karnik, Luis Figueira, J. Paulo Davim, Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts International Journal of Refractory Metals & Hard Materials. ,vol. 27, pp. 754- 763 ,(2009) , 10.1016/J.IJRMHM.2008.12.007
A.K.M. Nurul Amin, Shuriani Binti Dolah, Marlina Binti Mahmud, M.A. Lajis, Effects of workpiece preheating on surface roughness, chatter and tool performance during end milling of hardened steel D2 Journal of Materials Processing Technology. ,vol. 201, pp. 466- 470 ,(2008) , 10.1016/J.JMATPROTEC.2007.11.304
W. Grzesik, Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools Wear. ,vol. 265, pp. 327- 335 ,(2008) , 10.1016/J.WEAR.2007.11.001
M.C. Shaw, A. Vyas, The Mechanism of Chip Formation with Hard Turning Steel CIRP Annals. ,vol. 47, pp. 77- 82 ,(1998) , 10.1016/S0007-8506(07)62789-9
Yong Huang, Steven Y. Liang, Modeling of Cutting Forces Under Hard Turning Conditions Considering Tool Wear Effect Journal of Manufacturing Science and Engineering-transactions of The Asme. ,vol. 127, pp. 262- 270 ,(2005) , 10.1115/1.1852571
M.C. Shaw, A. Vyas, Chip Formation in the Machining of Hardened Steel Cirp Annals-manufacturing Technology. ,vol. 42, pp. 29- 33 ,(1993) , 10.1016/S0007-8506(07)62385-3
Takashi Ueda, Mahfudz Al Huda, Keiji Yamada, Kazuo Nakayama, Hideaki Kudo, Temperature Measurement of CBN Tool in Turning of High Hardness Steel Cirp Annals-manufacturing Technology. ,vol. 48, pp. 63- 66 ,(1999) , 10.1016/S0007-8506(07)63132-1
T. I. El-Wardany, H. A. Kishawy, M. A. Elbestawi, Surface Integrity of Die Material in High Speed Hard Machining, Part 1: Micrographical Analysis Journal of Manufacturing Science and Engineering-transactions of The Asme. ,vol. 122, pp. 620- 631 ,(2000) , 10.1115/1.1286367