Effect of carbon on mechanically induced self-sustaining reactions (MSR) in TiO2–Al–C mixtures
作者： N. Setoudeh , N.J. Welham
DOI: 10.1016/J.IJRMHM.2015.07.036
关键词:
摘要: Abstract Mixtures of titanium dioxide, aluminium powder and activated carbon with different mass ratios were prepared milled for times. The amount used increased from 0% to 100% that required formation TiC study the effect on initiation a self - sustaining mechanochemical reaction in TiO2-Al-C mixtures. XRD results indicated by increasing fraction products changed Al3Ti Al2O3 include amounts Al2O3. Results also could be initiated during milling but only samples high carbon. In sample molar ratio TiO2:Al:C = 3:4:3, between raw materials was complete within 5 h time when detected.
sci-hub.se 参考文章(25)
Edmund Kugler Storms, The Refractory carbides Academic. ,(1967)
Ruiming Ren, Zhenguo Yang, LL Shaw, Polymorphic transformation and powder characteristics of TiO2 during high energy milling Journal of Materials Science. ,vol. 35, pp. 6015- 6026 ,(2000) , 10.1023/A:1026751017284
C.F. Feng, L. Froyen, Formation of Al3Ti and Al2O3 from an Al–TiO2 system for preparing in-situ aluminium matrix composites Composites Part A-applied Science and Manufacturing. ,vol. 31, pp. 385- 390 ,(2000) , 10.1016/S1359-835X(99)00041-X
M.A. Khaghani-Dehaghani, R. Ebrahimi-Kahrizsangi, N. Setoudeh, B. Nasiri-Tabrizi, Mechanochemical synthesis of Al2O3–TiB2 nanocomposite powder from Al–TiO2–H3BO3 mixture International Journal of Refractory Metals and Hard Materials. ,vol. 29, pp. 244- 249 ,(2011) , 10.1016/J.IJRMHM.2010.11.001
Laszlo Takacs, Self-sustaining reactions induced by ball milling Progress in Materials Science. ,vol. 47, pp. 355- 414 ,(2002) , 10.1016/S0079-6425(01)00002-0
Zhiguang Liu, Stiliana Raynova, Deliang Zhang, Brian Gabbitas, Study on the self sustained reactions in an Al–TiO2 composite powder produced by high-energy mechanical milling Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 449, pp. 1107- 1110 ,(2007) , 10.1016/J.MSEA.2006.03.135
H. Amel-Farzad, J. Vahdati-Khaki, A. Haerian, A. Youssefi, Combustion wave stability in diluted TiO2/Al/C system in atmospheric air Solid State Sciences. ,vol. 10, pp. 1958- 1969 ,(2008) , 10.1016/J.SOLIDSTATESCIENCES.2008.03.003
N. Setoudeh, N.J. Welham, Ball milling induced reduction of SrSO4 by Al International Journal of Mineral Processing. ,vol. 98, pp. 214- 218 ,(2011) , 10.1016/J.MINPRO.2010.12.002
N.J. Welham, J.S. Williams, Extended milling of graphite and activated carbon Carbon. ,vol. 36, pp. 1309- 1315 ,(1998) , 10.1016/S0008-6223(98)00111-0
J.H. Lee, S.K. Ko, C.W. Won, Combustion characteristics of TiO2/Al/C system Materials Research Bulletin. ,vol. 36, pp. 1157- 1167 ,(2001) , 10.1016/S0025-5408(01)00612-2