Analysis of Machining Time and Material Removal Performance as Factors Influencing Efficiency and Profitability
作者： Janos Kundrak , Viktor Molnar , Istvan Deszpoth
DOI: 10.1007/978-3-319-75677-6_22
关键词:
摘要: In the automotive industry, machining of hardened surfaces has become a serious topic in terms its manufacturing and economic efficiency recent decades. The reasons for this are difficulty components need that results increased accuracy surface quality. addition to grinding as conventional fine finishing procedure substituting procedures such hard turning have appeared. They can be applied reach quality values equal those grinding. This paper analyzes different (conventional bore grinding, combined procedure) on internal cylindrical surfaces, compared them time parameters practical material removal rate an parameter removal. While allows efficiency-based comparison identical or (machining with abrasive single-point tools), while (mainly operation time) aim at direct comparability costs procedures. cost-related relationships also analyzed.
springer.com
sci-hub.se 参考文章(15)
István Deszpoth, János Kundrák, Viktor Molnár, Komparativna studija skidanja materijala u strojnoj obradi tvrdih površina provrtanih rupa Tehnicki Vjesnik-technical Gazette. ,vol. 21, pp. 183- 189 ,(2014)
Philippe Revel, Nabil Jouini, Guillaume Thoquenne, Fabien Lefebvre, High precision hard turning of AISI 52100 bearing steel Precision Engineering-journal of The International Societies for Precision Engineering and Nanotechnology. ,vol. 43, pp. 24- 33 ,(2016) , 10.1016/J.PRECISIONENG.2015.06.006
H.K. Tönshoff, C. Arendt, R. Ben Amor, Cutting of Hardened Steel CIRP Annals. ,vol. 49, pp. 547- 566 ,(2000) , 10.1016/S0007-8506(07)63455-6
Y.B. Guo, A.W. Warren, The impact of surface integrity by hard turning vs. grinding on fatigue damage mechanisms in rolling contact Surface & Coatings Technology. ,vol. 203, pp. 291- 299 ,(2008) , 10.1016/J.SURFCOAT.2008.09.005
Youngsik Choi, A Comparative Study of Residual Stress Distribution Induced by Hard Machining Versus Grinding Tribology Letters. ,vol. 36, pp. 277- 284 ,(2009) , 10.1007/S11249-009-9512-9
F. Klocke, E. Brinksmeier, K. Weinert, Capability Profile of Hard Cutting and Grinding Processes CIRP Annals. ,vol. 54, pp. 22- 45 ,(2005) , 10.1016/S0007-8506(07)60018-3
Dipti Kanta Das, Ashok Kumar Sahoo, Ratnakar Das, B.C. Routara, Investigations on Hard Turning Using Coated Carbide Insert: Grey based Taguchi and Regression Methodology Procedia Materials Science. ,vol. 6, pp. 1351- 1358 ,(2014) , 10.1016/J.MSPRO.2014.07.114
Y.B Guo, J Sahni, A comparative study of hard turned and cylindrically ground white layers International Journal of Machine Tools & Manufacture. ,vol. 44, pp. 135- 145 ,(2004) , 10.1016/J.IJMACHTOOLS.2003.10.009
J. Kundrák, A. Markopoulos, A. G. Mamalis, Finishing of Hardened Boreholes: Grinding or Hard Cutting? Materials and Manufacturing Processes. ,vol. 19, pp. 979- 993 ,(2004) , 10.1081/LMMP-200034480
Gustavo de Siqueira Galoppi, Marco Stipkovic Filho, Gilmar Ferreira Batalha, Hard turning of tempered DIN 100Cr6 steel with coated and no coated CBN inserts Journal of Materials Processing Technology. ,vol. 179, pp. 146- 153 ,(2006) , 10.1016/J.JMATPROTEC.2006.03.067