Characteristics of machined surface integrity in face milling Al-Li alloy 2A97 with carbide inserts
作者： Jintao Niu , Zhanqiang Liu , Xing Ai , Weimin Huang , Guijie Wang
DOI: 10.1007/S00170-018-2907-8
关键词:
摘要: … Residual stresses on machined surfaces were measured on the basis of cosα method using a μ-X360 X-ray residual stress analyzer (Pulstec Industrial Co., Ltd.) equipped with CrKβ …
springer.com
sci-hub.se 参考文章(31)
Hadi Moradi, None, OPTIMIZATION OF CUTTING PARAMETERS FOR POCKET MILLING ON THE SKIN PLATE IN AL AND AL-LI MATERIALS ,(2014)
Xiaoming Zhang, Haikuo Mu, Xinda Huang, Zhongtao Fu, Dahu Zhu, Han Ding, Cryogenic Milling of Aluminium-lithium Alloys: Thermo-mechanical Modelling towards Fine-tuning of Part Surface Residual Stress Procedia CIRP. ,vol. 31, pp. 160- 165 ,(2015) , 10.1016/J.PROCIR.2015.03.055
Chong Gao, Rongqiang Gao, Yue Ma, Microstructure and mechanical properties of friction spot welding aluminium–lithium 2A97 alloy Materials & Design. ,vol. 83, pp. 719- 727 ,(2015) , 10.1016/J.MATDES.2015.06.013
Zhaoju Zhu, Jie Sun, Jianfeng Li, Panling Huang, Investigation on the influence of tool wear upon chip morphology in end milling titanium alloy Ti6Al4V The International Journal of Advanced Manufacturing Technology. ,vol. 83, pp. 1477- 1485 ,(2016) , 10.1007/S00170-015-7690-1
Yifeng Xiong, Wenhu Wang, Ruisong Jiang, Kunyang Lin, Guodong Song, Surface integrity of milling in-situ TiB2 particle reinforced Al matrix composites International Journal of Refractory Metals & Hard Materials. ,vol. 54, pp. 407- 416 ,(2016) , 10.1016/J.IJRMHM.2015.09.007
Wesley A. Tayon, Marcia S. Domack, Eric K. Hoffman, Stephen J. Hales, Texture Evolution within the Thermomechanically Affected Zone of an Al-Li Alloy 2195 Friction Stir Weld Metallurgical and Materials Transactions A. ,vol. 44, pp. 4906- 4913 ,(2013) , 10.1007/S11661-013-1802-Z
Yi LIN, Zi-qiao ZHENG, Hai-feng ZHANG, Ye HAN, Effect of heat treatment process on tensile properties of 2A97 Al−Li alloy: Experiment and BP neural network simulation Transactions of Nonferrous Metals Society of China. ,vol. 23, pp. 1728- 1736 ,(2013) , 10.1016/S1003-6326(13)62655-2
M.L. Rahaman, Liangchi Zhang, Mei Liu, Weidong Liu, Surface roughness effect on the friction and wear of bulk metallic glasses Wear. ,vol. 332, pp. 1231- 1237 ,(2015) , 10.1016/J.WEAR.2014.11.030
Khaider Bouacha, Mohamed Athmane Yallese, Tarek Mabrouki, Jean-François Rigal, Statistical analysis of surface roughness and cutting forces using response surface methodology in hard turning of AISI 52100 bearing steel with CBN tool International Journal of Refractory Metals & Hard Materials. ,vol. 28, pp. 349- 361 ,(2010) , 10.1016/J.IJRMHM.2009.11.011
Xiu Li Fu, Zeng Hui An, Yang Qiao, Xiu Hua Men, Influence of Work-Hardening on Wear Resistance of Machined Surface of Aviation Aluminum Alloy Key Engineering Materials. pp. 117- 121 ,(2013) , 10.4028/WWW.SCIENTIFIC.NET/KEM.589-590.117