Investigation of tribological properties of boronized Fe-based SAE 1020 and TS-DDK 40 journal bearings at high loads
作者： Bekir Sadık Ünlü , Enver Atik
DOI: 10.1016/J.MATDES.2009.10.041
关键词:
摘要: Abstract In practice, ferrous based materials are not used because they show similar properties to shaft material and known cause adhesive wear in journal bearings. With boronizing process, can significantly be decreased. this study, has been applied some (SAE 1020, TS-DDK 40) Wear experiments were done on SAE 1050 steel as counter abrader with 100 N loads, 1500 rpm for 5 h by using a radial bearing test rig. Boronizing treatment increased resistance of 40 about 10–25, 5–7 times respectively.
elsevier.com
sci-hub.se 参考文章(15)
Ozkan Ozdemir, Metin Usta, Cuma Bindal, A.Hikmet Ucisik, Hard iron boride (Fe2B) on 99.97wt% pure iron Vacuum. ,vol. 80, pp. 1391- 1395 ,(2006) , 10.1016/J.VACUUM.2006.01.022
Bharat Bhushan, Principles and Applications of Tribology ,(1999)
Salim Sahin, Cevdet Meric, Investigation of the effect of boronizing on cast irons Materials Research Bulletin. ,vol. 37, pp. 971- 979 ,(2002) , 10.1016/S0025-5408(02)00697-9
Cevdet Meriç, Salim Sahin, Selim Sarper Yilmaz, Investigation of the effect on boride layer of powder particle size used in boronizing with solid boron-yielding substances Materials Research Bulletin. ,vol. 35, pp. 2165- 2172 ,(2000) , 10.1016/S0025-5408(00)00427-X
C. Meric, S. Sahin, B. Backir, N.S. Koksal, Investigation of the boronizing effect on the abrasive wear behavior in cast irons Materials & Design. ,vol. 27, pp. 751- 757 ,(2006) , 10.1016/J.MATDES.2005.01.018
H. Sert, A. Can, H. Arıkan, B. Selcuk, H. Toprak, Wear behavior of different surface treated cam spindles Wear. ,vol. 260, pp. 1013- 1019 ,(2006) , 10.1016/J.WEAR.2005.06.012
C. Meric, S. Sahin, M. Uzkut, Investigation of effect of boronising on welding zone Science and Technology of Welding and Joining. ,vol. 7, pp. 107- 110 ,(2002) , 10.1179/136217102225002637
Enver Atık, Umut Yunker, Cevdet Merıç, The effects of conventional heat treatment and boronizing on abrasive wear and corrosion of SAE 1010, SAE 1040, D2 and 304 steels Tribology International. ,vol. 36, pp. 155- 161 ,(2003) , 10.1016/S0301-679X(02)00069-5
Ugur Sen, Saduman Sen, Fevzi Yilmaz, Structural characterization of boride layer on boronized ductile irons Surface & Coatings Technology. ,vol. 176, pp. 222- 228 ,(2004) , 10.1016/S0257-8972(03)00731-X
R İpek, B Selçuk, M.B Karamiş, V Kuzucu, A Yücel, An evaluation of the possibilities of using borided GG25 cast iron instead of chilled GG25 cast iron (surface properties) Journal of Materials Processing Technology. ,vol. 105, pp. 73- 79 ,(2000) , 10.1016/S0924-0136(00)00571-9