Roughness optimization of flow-formed tubes using the Taguchi method
作者： Amin Abedini , Samrand Rash Ahmadi , Ali Doniavi
DOI: 10.1007/S00170-014-5732-8
关键词:
摘要: The present study reports the effect of various flow-forming process parameters and roller geometry on roughness flow-formed tubes commercial pure copper UNS C11000. Thickness reduction ratio, feed rate, angular speed mandrel, attack angle roller, tip radius, smooth were considered as variable parameters. effects these input have been critically analyzed using Taguchi method. Through ANOVA analysis, it has found that radius is most important parameter affecting followed by thickness ratio. Selection an optimum combination was performed based “average results.” minimum 1.37 μm achieved when set at their values.
springer.com
sci-hub.se 参考文章(14)
Glenn Lion Gardiner, Materials and Processes in Manufacturing ,(1974)
M. Joseph Davidson, K. Balasubramanian, G.R.N. Tagore, Experimental investigation on flow-forming of AA6061 alloy—A Taguchi approach Journal of Materials Processing Technology. ,vol. 200, pp. 283- 287 ,(2008) , 10.1016/J.JMATPROTEC.2007.09.026
M. Joseph Davidson, K. Balasubramanian, G.R.N. Tagore, An experimental study on the quality of flow-formed AA6061 tubes Journal of Materials Processing Technology. ,vol. 203, pp. 321- 325 ,(2008) , 10.1016/J.JMATPROTEC.2007.10.021
M.O. Lai, K.S. Lee, Fracture and creep properties of flow-formed tubes Journal of Materials Processing Technology. ,vol. 29, pp. 321- 330 ,(1992) , 10.1016/0924-0136(92)90446-Y
Q.X. Xia, X.Q. Cheng, Y. Hu, F. Ruan, Finite element simulation and experimental investigation on the forming forces of 3D non-axisymmetrical tubes spinning International Journal of Mechanical Sciences. ,vol. 48, pp. 726- 735 ,(2006) , 10.1016/J.IJMECSCI.2006.01.014
Bikramjit Podder, Chandan Mondal, K. Ramesh Kumar, D.R. Yadav, Effect of preform heat treatment on the flow formability and mechanical properties of AISI4340 steel Materials & Design. ,vol. 37, pp. 174- 181 ,(2012) , 10.1016/J.MATDES.2012.01.002
H. Yang, J.H. Zhang, Y.L. Xu, F. Ma, M. Zhan, 3D FEM analysis of influence of roller feed rate on forming force and quality of cone spinning Journal of Materials Processing Technology. ,vol. 187, pp. 486- 491 ,(2007) , 10.1016/J.JMATPROTEC.2006.11.114
P.M. George, B.K. Raghunath, L.M. Manocha, Ashish M. Warrier, EDM machining of carbon–carbon composite—a Taguchi approach Journal of Materials Processing Technology. ,vol. 145, pp. 66- 71 ,(2004) , 10.1016/S0924-0136(03)00863-X
Hamid R. Molladavoudi, Faramarz Djavanroodi, Experimental study of thickness reduction effects on mechanical properties and spinning accuracy of aluminum 7075-O, during flow forming The International Journal of Advanced Manufacturing Technology. ,vol. 52, pp. 949- 957 ,(2011) , 10.1007/S00170-010-2782-4
Sabahudin Ekinovic, Edin Begovic, Ibrahim Plancic, Influence of Flow-Forming Process on Cutting Force Changes in Machining of 99.5% Al Workpiece Materials and Manufacturing Processes. ,vol. 27, pp. 791- 796 ,(2012) , 10.1080/10426914.2011.647941