A NEW APPROACH FOR ACHIEVING EXCELLENT STRAIN HOMOGENEITY IN TUBULAR CHANNEL ANGULAR PRESSING (TCAP) PROCESS
作者： G Faraji , M Baniasadi , F Reshadi
DOI:
关键词:
摘要: Tubular channel angular pressing Trapezoidal geometry Finite element method Plastic deformation (TCAP) is a recently invented severe plastic technique for producing UFG tubes. analysis using the finite (FEM) was carried out to investigate effects of trapezoidal on strain inhomogeneity index (SII), level and required load compared previously-used geometries. The results showed that SII decreases 0.003 in case while it 0.13 0.24 cases semicircular triangular types, respectively. It means excellent homogeneity achieved TCAP processing geometry. 41% lower than but almost same channel. From point view better requiring process load, an
参考文章(24)
Ruslan Z. Valiev, Terence G. Langdon, Principles of equal-channel angular pressing as a processing tool for grain refinement Progress in Materials Science. ,vol. 51, pp. 881- 981 ,(2006) , 10.1016/J.PMATSCI.2006.02.003
L TOTH, M ARZAGHI, J FUNDENBERGER, B BEAUSIR, O BOUAZIZ, R ARRUFFATMASSION, Severe plastic deformation of metals by high-pressure tube twisting Scripta Materialia. ,vol. 60, pp. 175- 177 ,(2009) , 10.1016/J.SCRIPTAMAT.2008.09.029
Cheng Xu, Minoru Furukawa, Zenji Horita, Terence G Langdon, Using ECAP to achieve grain refinement, precipitate fragmentation and high strain rate superplasticity in a spray-cast aluminum alloy Acta Materialia. ,vol. 51, pp. 6139- 6149 ,(2003) , 10.1016/S1359-6454(03)00433-6
Y. Saito, H. Utsunomiya, N. Tsuji, T. Sakai, Novel ultra-high straining process for bulk materials—development of the accumulative roll-bonding (ARB) process Acta Materialia. ,vol. 47, pp. 579- 583 ,(1999) , 10.1016/S1359-6454(98)00365-6
G. Faraji, M. M. Mashhadi, K. Abrinia, H. S. Kim, Deformation behavior in the tubular channel angular pressing (TCAP) as a noble SPD method for cylindrical tubes Applied Physics A. ,vol. 107, pp. 819- 827 ,(2012) , 10.1007/S00339-012-6809-6
N. Pardis, R. Ebrahimi, Deformation behavior in Simple Shear Extrusion (SSE) as a new severe plastic deformation technique Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 527, pp. 355- 360 ,(2009) , 10.1016/J.MSEA.2009.08.051
A.V. Nagasekhar, S.C. Yoon, Y. Tick-Hon, H.S. Kim, An experimental verification of the finite element modelling of equal channel angular pressing Computational Materials Science. ,vol. 46, pp. 347- 351 ,(2009) , 10.1016/J.COMMATSCI.2009.03.018
Ghader Faraji, Alireza Babaei, Mahmoud Mosavi Mashhadi, Karen Abrinia, Parallel tubular channel angular pressing (PTCAP) as a new severe plastic deformation method for cylindrical tubes Materials Letters. ,vol. 77, pp. 82- 85 ,(2012) , 10.1016/J.MATLET.2012.03.007
Hyoung Seop Kim, Finite element analysis of deformation behaviour of metals during equal channel multi-angular pressing Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 328, pp. 317- 323 ,(2002) , 10.1016/S0921-5093(01)01793-2
M. Shahbaz, N. Pardis, R. Ebrahimi, B. Talebanpour, A novel single pass severe plastic deformation technique: Vortex extrusion Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 530, pp. 469- 472 ,(2011) , 10.1016/J.MSEA.2011.09.114