Oven Sintering Process Optimization for Inkjet-Printed Ag Nanoparticle Ink
作者： Kauko Ostman , Ana Lopez Cabezas , Matti Mantysalo , Eerik Halonen , Tanja Viiru
DOI: 10.1109/TCPMT.2012.2226458
关键词:
摘要: This paper focuses on optimizing the oven sintering time and temperature for inkjet-printed silver nanoparticle ink a polyimide substrate. Two basic aspects in fabricating conductor structures printable electronics are conductivity adhesion between substrate material. Conductivity evolution during is monitored with real-time resistance measurements at five different temperatures. Based results, evaluated several points three The higher temperature, faster reach their maximum values. lowest resistivity values below 4 μΩ· cm. However, each it takes longer to best In this paper, we aim better understand of nanoparticles determine conditions (temperature, time) our particular ink-substrate combination. results can be used further define optimum printed inks polymer substrates.
sci-hub.se 参考文章(26)
Kazuhiro Murata, Junichi Matsumoto, Akira Tezuka, Yorishige Matsuba, Hiroshi Yokoyama, Super-fine ink-jet printing: toward the minimal manufacturing system symposium on design test integration and packaging of mems moems. ,vol. 12, pp. 2- 7 ,(2005) , 10.1007/S00542-005-0023-9
Sung-Cheol Park, Young-Bae Park, Effect of Temperature/Humidity Treatment Conditions on Interfacial Adhesion Energy between Inkjet-Printed Ag and Polyimide Japanese Journal of Applied Physics. ,vol. 48, ,(2009) , 10.1143/JJAP.48.08HL02
Ville Pekkanen, Kimmo Kaija, Matti Mäntysalo, Esa Kunnari, Juha Niittynen, Pauliina Mansikkamäki, Functional fluid jetting performance optimization Microelectronics Reliability. ,vol. 50, pp. 864- 871 ,(2010) , 10.1016/J.MICROREL.2010.02.002
Matti Mantysalo, Pauliina Mansikkamaki, Jani Miettinen, Kimmo Kaija, Seppo Pienimaa, Risto Ronkka, Kenichi Hashizume, Akiko Kamigori, Yorishige Matsuba, Kenshu Oyama, Nobuto Terada, Hiroshi Saito, Mikiharu Kuchiki, Mikihiko Tsubouchi, Evaluation of Inkjet Technology for Electronic Packaging and System Integration electronic components and technology conference. pp. 89- 94 ,(2007) , 10.1109/ECTC.2007.373781
Aurore Denneulin, Anne Blayo, Charles Neuman, Julien Bras, Infra-red assisted sintering of inkjet printed silver tracks on paper substrates Journal of Nanoparticle Research. ,vol. 13, pp. 3815- 3823 ,(2011) , 10.1007/S11051-011-0306-2
A. Sridhar, D.J. van Dijk, R. Akkerman, Inkjet printing and adhesion characterisation of conductive tracks on a commercial printed circuit board material Thin Solid Films. ,vol. 517, pp. 4633- 4637 ,(2009) , 10.1016/J.TSF.2009.03.133
Myong-Ki Kim, Heui-Seok Kang, Kyung-Tae Kang, Sang-Ho Lee, Jun-Young Hwang, Seung-Jae Moon, Laser Sintering of Inkjet-Printed Silver Lines on Glass and PET Substrates Transactions of The Korean Society of Mechanical Engineers B. ,vol. 34, pp. 975- 982 ,(2010) , 10.3795/KSME-B.2010.34.11.975
Tero Kumpulainen, Jussi Pekkanen, Jani Valkama, Jarmo Laakso, Reijo Tuokko, Matti Mäntysalo, Low temperature nanoparticle sintering with continuous wave and pulse lasers Optics and Laser Technology. ,vol. 43, pp. 570- 576 ,(2011) , 10.1016/J.OPTLASTEC.2010.08.002
Hyun Chul Jung, Su-Hwan Cho, Jae Woo Joung, Yong-Soo Oh, Studies on Inkjet-Printed Conducting Lines for Electronic Devices Journal of Electronic Materials. ,vol. 36, pp. 1211- 1218 ,(2007) , 10.1007/S11664-007-0194-5
R.A. Street, W.S. Wong, S.E. Ready, M.L. Chabinyc, A.C. Arias, S. Limb, A. Salleo, R. Lujan, Jet printing flexible displays Materials Today. ,vol. 9, pp. 32- 37 ,(2006) , 10.1016/S1369-7021(06)71445-6