Study on tribological properties of Al-TiC composites by Taguchi method
作者： Eshan Agrawal , Vinod Tungikar
DOI: 10.1016/J.MATPR.2020.02.486
关键词: Reinforcement 、 Design of experiments 、 Metal matrix composite 、 Composite material 、 Centrifugal casting (industrial) 、 Taguchi methods 、 Tribology 、 Aluminium 、 Composite number 、 Materials science
摘要: … of TiC content improves the corrosion resistance [43]. In the present work Al-TiC composite … the effect of TiC particles on specific wear rate and co efficient of friction for the prepared …
sci-hub.se 参考文章(41)
Pardeep Sharma, Dinesh Khanduja, Satpal Sharma, Dry sliding wear investigation of Al6082/Gr metal matrix composites by response surface methodology Journal of materials research and technology. ,vol. 5, pp. 29- 36 ,(2016) , 10.1016/J.JMRT.2015.05.001
Anand Kumar, Manas Mohan Mahapatra, Pradeep Kumar Jha, Fabrication and Characterizations of Mechanical Properties of Al-4.5%Cu/10TiC Composite by In-situ Method Journal of Minerals and Materials Characterization and Engineering. ,vol. 11, pp. 1075- 1080 ,(2012) , 10.4236/JMMCE.2012.1111113
Xuedong Lin, Changming Liu, Haibo Xiao, Fabrication of Al–Si–Mg functionally graded materials tube reinforced with in situ Si/Mg2Si particles by centrifugal casting Composites Part B-engineering. ,vol. 45, pp. 8- 21 ,(2013) , 10.1016/J.COMPOSITESB.2012.09.001
Nassim Samer, Jérôme Andrieux, Bruno Gardiola, Nikhil Karnatak, Olivier Martin, Hiroki Kurita, Laurent Chaffron, Sophie Gourdet, Sabine Lay, Olivier Dezellus, Microstructure and mechanical properties of an Al–TiC metal matrix composite obtained by reactive synthesis Composites Part A-applied Science and Manufacturing. ,vol. 72, pp. 50- 57 ,(2015) , 10.1016/J.COMPOSITESA.2015.02.001
T.P.D. Rajan, R.M. Pillai, B.C. Pai, Characterization of centrifugal cast functionally graded aluminum-silicon carbide metal matrix composites Materials Characterization. ,vol. 61, pp. 923- 928 ,(2010) , 10.1016/J.MATCHAR.2010.06.002
P.Sriram Murthy Y.Seetha Rama Rao, Evaluation of mechanical properties of aluminium alloy–alumina–boron carbide metal matrix composites Materials & Design. ,vol. 58, pp. 332- 338 ,(2014) , 10.1016/J.MATDES.2014.01.068
Jarosław Woźniak, Bogusława Adamczyk-Cieślak, Marek Kostecki, Kamil Broniszewski, Włodzimierz Bochniak, Andrzej Olszyna, Influence of cooling condition on properties of extruded aluminum alloy matrix composites Composites Part B-engineering. ,vol. 77, pp. 100- 104 ,(2015) , 10.1016/J.COMPOSITESB.2015.03.018
Masoud Mohammadi Rahvard, Morteza Tamizifar, Seyed Mohammad Ali Boutorabi, Sajad Gholami Shiri, Characterization of the graded distribution of primary particles and wear behavior in the A390 alloy ring with various Mg contents fabricated by centrifugal casting Materials & Design. ,vol. 56, pp. 105- 114 ,(2014) , 10.1016/J.MATDES.2013.10.070
Ehsan Ghasali, Masoud Alizadeh, Touradj Ebadzadeh, Amir hossein Pakseresht, Ali Rahbari, Investigation on microstructural and mechanical properties of B4C–aluminum matrix composites prepared by microwave sintering Journal of materials research and technology. ,vol. 4, pp. 411- 415 ,(2015) , 10.1016/J.JMRT.2015.02.005
Shivaji V. Gawal, Vinod B. Tungikar, Wear Predictions of Metal Matrix Composite in Presence of Greasing Material Energy and Power Engineering. ,vol. 4, pp. 173- 177 ,(2012) , 10.4236/EPE.2012.43024