Cold spray deposition of 316L stainless steel coatings on aluminium surface with following laser post-treatment
作者： A. Sova , S. Grigoriev , A. Okunkova , I. Smurov
DOI: 10.1016/J.SURFCOAT.2013.07.052
关键词: Aluminium 、 Substrate (electronics) 、 Deposition (phase transition) 、 Porosity 、 Indentation hardness 、 Gas dynamic cold spray 、 Metallurgy 、 Materials science 、 Particle-size distribution 、 Coating
摘要: … powder has higher microhardness than the one deposited using fine powder, whereas adhesion does not depend on powder … In order to test the influence of nozzle scanning velocity on …
elsevier.com
sci-hub.se 参考文章(13)
Hamid Assadi, Frank Gärtner, Thorsten Stoltenhoff, Heinrich Kreye, Bonding mechanism in cold gas spraying Acta Materialia. ,vol. 51, pp. 4379- 4394 ,(2003) , 10.1016/S1359-6454(03)00274-X
T. Marrocco, T. Hussain, D. G. McCartney, P. H. Shipway, Corrosion Performance of Laser Posttreated Cold Sprayed Titanium Coatings Journal of Thermal Spray Technology. ,vol. 20, pp. 909- 917 ,(2011) , 10.1007/S11666-011-9637-X
Wen-Ya Li, Hanlin Liao, G. Douchy, C. Coddet, Optimal design of a cold spray nozzle by numerical analysis of particle velocity and experimental validation with 316L stainless steel powder Materials & Design. ,vol. 28, pp. 2129- 2137 ,(2007) , 10.1016/J.MATDES.2006.05.016
Heli Koivuluoto, Petri Vuoristo, Effect of Powder Type and Composition on Structure and Mechanical Properties of Cu + Al2O3 Coatings Prepared by using Low-Pressure Cold Spray Process Journal of Thermal Spray Technology. ,vol. 19, pp. 1081- 1092 ,(2010) , 10.1007/S11666-010-9491-2
H. Assadi, T. Schmidt, H. Richter, J.-O. Kliemann, K. Binder, F. Gärtner, T. Klassen, H. Kreye, On Parameter Selection in Cold Spraying Journal of Thermal Spray Technology. ,vol. 20, pp. 1161- 1176 ,(2011) , 10.1007/S11666-011-9662-9
T. Hussain, D. G. McCartney, P. H. Shipway, D. Zhang, Bonding Mechanisms in Cold Spraying: The Contributions of Metallurgical and Mechanical Components Journal of Thermal Spray Technology. ,vol. 18, pp. 364- 379 ,(2009) , 10.1007/S11666-009-9298-1
T. Schmidt, F. Gaertner, H. Kreye, New developments in cold spray based on higher gas and particle temperatures Journal of Thermal Spray Technology. ,vol. 15, pp. 488- 494 ,(2006) , 10.1361/105996306X147144
K. Spencer, D.M. Fabijanic, M.-X. Zhang, The influence of Al2O3 reinforcement on the properties of stainless steel cold spray coatings Surface & Coatings Technology. ,vol. 206, pp. 3275- 3282 ,(2012) , 10.1016/J.SURFCOAT.2012.01.031
P. Poza, C.J. Múnez, M.A. Garrido, S. Vezzù, S. Rech, A. Trentin, RETRACTED: Effect of laser remelting on the mechanical behaviour of Inconel 625 cold-sprayed coatings Procedia Engineering. ,vol. 10, pp. 3799- 3804 ,(2011) , 10.1016/J.PROENG.2011.06.002
Eric Irissou, Jean-Gabriel Legoux, Bernard Arsenault, Christian Moreau, Investigation of Al-Al2O3 Cold Spray Coating Formation and Properties Journal of Thermal Spray Technology. ,vol. 16, pp. 661- 668 ,(2007) , 10.1007/S11666-007-9086-8