Machining of Hypereutectic Aluminum Silicon Alloys
作者： Eckart Uhlmann , Karsten Flögel , Fiona Sammler , Iris Rieck , Arne Dethlefs
DOI: 10.1016/J.PROCIR.2014.03.069
关键词:
摘要: In the work presented in this paper, combined machining of hypereutectic G-AlSi17Cu4Mg with abrasive water jet turning (AWJT) as a roughing process and conventional finishing was studied. The duration single processing steps estimated compared to length process. tool life AWJT at least 10 hours material removal rate up 13cm3/min low temperatures give cutting technology very high potential. Furthermore close surface is impacted less by process, comparison rough turning. results obtained showed that generates parts qualities further optimization may be possible substitution productivity.
core.ac.uk
cyberleninka.org
sci-hub.se 参考文章(10)
O. Lemmer, R. Cremer, D. Breidt, M. Frank, CVD‐Diamant‐Dünnschichten nach dem Hot‐Filament‐Verfahren Wiley‐VCH Verlag GmbH & Co. KGaA. pp. 95- 109 ,(2005) , 10.1002/3527604278.CH6
Eckart Uhlmann, Karsten Flögel, Michael Kretzschmar, Fabian Faltin, Abrasive Waterjet Turning of High Performance Materials Procedia CIRP. ,vol. 1, pp. 409- 413 ,(2012) , 10.1016/J.PROCIR.2012.04.073
A. Inspektor, E.J. Oles, C.E. Bauer, Theory and practice in diamond coated metal-cutting tools International Journal of Refractory Metals & Hard Materials. ,vol. 15, pp. 49- 56 ,(1997) , 10.1016/S0263-4368(96)00045-5
Eckart Uhlmann, Fiona Sammler, CVD Coated Diamond Tools for the Machining of Lightweight Materials Advanced Materials Research. ,vol. 907, pp. 63- 73 ,(2014) , 10.4028/WWW.SCIENTIFIC.NET/AMR.907.63
M. Lahres, G. Jörgensen, Properties and dry cutting performance of diamond-coated tools Surface & Coatings Technology. ,vol. 96, pp. 198- 204 ,(1997) , 10.1016/S0257-8972(97)00108-4
Y. Kevin Chou, Jie Liu, CVD diamond tool performance in metal matrix composite machining Surface & Coatings Technology. ,vol. 200, pp. 1872- 1878 ,(2005) , 10.1016/J.SURFCOAT.2005.08.094
Angéline Poulon-Quintin, Cyril Faure, Lionel Teulé-Gay, Jean-Pierre Manaud, Bilayer systems of tantalum or zirconium nitrides and molybdenum for optimized diamond deposition Thin Solid Films. ,vol. 519, pp. 1600- 1605 ,(2010) , 10.1016/J.TSF.2010.08.011
E. Uhlmann, W. Reimers, F. Byrne, M. Klaus, Analysis of tool wear and residual stress of CVD diamond coated cemented carbide tools in the machining of aluminium silicon alloys Production Engineering. ,vol. 4, pp. 203- 209 ,(2010) , 10.1007/S11740-010-0213-X
Prabhu U. Arumugam, Ajay P. Malshe, Stephen A. Batzer, Dry machining of aluminum-silicon alloy using polished CVD diamond-coated cutting tools inserts Surface & Coatings Technology. ,vol. 200, pp. 3399- 3403 ,(2006) , 10.1016/J.SURFCOAT.2005.08.127
Jens König, Herstellung und Einsatz CVD-diamantbeschichteter Bohrgewindefräser ,(2009) , 10.14279/DEPOSITONCE-2156