Deformation and fracture of Ti/439 stainless steel clad composite at intermediate temperatures
作者： Jong Su Ha , Sun Ig Hong
DOI: 10.1016/J.MSEA.2015.11.041
关键词:
摘要: … Ti/STS439 clad composites and we found that the ductility loss at intermediate temperatures in Ti… to carbon in STS439, not by DSA due to oxygen in Ti. We also observed wavy surface in …
elsevier.com
sci-hub.se 参考文章(19)
S. N. Polyanskii, Cladded Steel for the Oil and Gas Industries Chemical and Petroleum Engineering. ,vol. 38, pp. 703- 707 ,(2002) , 10.1023/A:1023355018056
Ju Young Jin, Sun Ig Hong, Effect of heat treatment on tensile deformation characteristics and properties of Al3003/STS439 clad composite Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 596, pp. 1- 8 ,(2014) , 10.1016/J.MSEA.2013.12.019
S. Dziallach, W. Bleck, M. Köhler, G. Nicolini, Roll‐Bonded Titanium/Stainless‐Steel Couples, Part 2: Mechanical Properties after Different Material‐Treatment Routes Advanced Engineering Materials. ,vol. 11, pp. 82- 87 ,(2009) , 10.1002/ADEM.200800277
Peter C Tortorici, M.A Dayananda, Phase formation and interdiffusion in Al-clad 430 stainless steels Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 244, pp. 207- 215 ,(1998) , 10.1016/S0921-5093(97)00534-0
M. Doner, H. Conrad, Deformation mechanisms in commercial Ti (0.5 at. pct oineq) at intermediate and high temperatures (0.3 - 0.6 tinm) Metallurgical Transactions. ,vol. 4, pp. 2809- 2817 ,(1973) , 10.1007/BF02644581
Sun Ig Hong, Influence of dynamic strain aging on the dislocation substructure in a uniaxial tension test Materials Science and Engineering. ,vol. 79, pp. 1- 7 ,(1986) , 10.1016/0025-5416(86)90380-0
Jong Su Ha, Sun Ig Hong, Design of high strength Cu alloy interlayer for mechanical bonding Ti to steel and characterization of their tri-layered clad Materials & Design. ,vol. 51, pp. 293- 299 ,(2013) , 10.1016/J.MATDES.2013.04.068
B. K. Choudhary, E. Isaac Samuel, G. Sainath, J. Christopher, M. D. Mathew, Influence of Temperature and Strain Rate on Tensile Deformation and Fracture Behavior of P92 Ferritic Steel Metallurgical and Materials Transactions A. ,vol. 44, pp. 4979- 4992 ,(2013) , 10.1007/S11661-013-1869-6
K.S. Lee, S.E. Lee, H.K. Sung, D.H. Lee, J.S. Kim, Y.W. Chang, S. Lee, Y.N. Kwon, Influence of reduction ratio on the interface microstructure and mechanical properties of roll-bonded Al/Cu sheets Materials Science and Engineering A-structural Materials Properties Microstructure and Processing. ,vol. 583, pp. 177- 181 ,(2013) , 10.1016/J.MSEA.2013.06.077
In-Kyu Kim, Sun Ig Hong, Effect of component layer thickness on the bending behaviors of roll-bonded tri-layered Mg/Al/STS clad composites Materials & Design. ,vol. 49, pp. 935- 944 ,(2013) , 10.1016/J.MATDES.2013.02.052