The Study on the Optimization of Injection Molding Process Parameters with Gray Relational Analysis
作者： Chin-Ping Fung , Cheng-Hung Huang , Ji-Liang Doong
DOI: 10.1177/0731684403022001843
关键词:
摘要: This paper studies the optimization of injection molding process parameters by using gray relational analysis method. Nine experimental runs based on Taguchi method’s orthogonal arrays are studied to pick best factor level condition. The mechanical properties yield stress and elongation selected be target quality. levels assessed according chosen two properties. degree influence that controllable factors exert is investigating correlation between them. From grade matrix, most influential easily influenced property can picked. It found melt temperature both elongation. more those than is. sequence importance affect yi...
sagepub.com
harvard.edu
sci-hub.se 参考文章(15)
J. L. Deng, Introduction to Grey system theory Journal of Grey System. ,vol. 1, pp. 1- 24 ,(1989) , 10.5555/90757.90758
S. F. Xavier, D. Tyagi, A. Misra, Influence of injection‐molding parameters on the morphology and mechanical properties of glass fiber‐reinforced polypropylene composites Polymer Composites. ,vol. 3, pp. 88- 96 ,(1982) , 10.1002/PC.750030207
Anne C. Shoemaker, Raghu N. Kacker, A methodology for planning experiments in robust product and process design Quality and Reliability Engineering International. ,vol. 4, pp. 95- 103 ,(1988) , 10.1002/QRE.4680040204
B. E. Ruiz De Gauna, M. Gaztelumendi, J. Nazábal, Processing and composition dependence of the structure and mechanical properties of polycarbonate/ultrax blends Polymer Composites. ,vol. 20, pp. 553- 564 ,(1999) , 10.1002/PC.10379
R. Singh, F. Chen, F. R. Jones, Injection molding of glass fiber reinforced phenolic composites. 2 : Study of the injection molding process Polymer Composites. ,vol. 19, pp. 37- 47 ,(1998) , 10.1002/PC.10073
Ming-Hsiung Ho, Jiun-Ren Hwang, Ji-Liang Doong, Chin-Ping Fung, Impact fatigue of a polycarbonate/acrylonitrile‐butadiene‐styrene blend Polymer Engineering and Science. ,vol. 39, pp. 708- 720 ,(1999) , 10.1002/PEN.11459
Roberto Greco, Maria Francesca Astarita, Lisong Dong, A. Sorrentino, Polycarbonate/ABS blends: Processability, thermal properties, and mechanical and impact behavior Advances in Polymer Technology. ,vol. 13, pp. 259- 274 ,(1994) , 10.1002/ADV.1994.060130402
T. P. Skourlis, C. Chassapis, S. Manoochehri, Fiber Orientation Morphological Layers in Injection Molded Long Fiber Reinforced Thermoplastics Journal of Thermoplastic Composite Materials. ,vol. 10, pp. 453- 475 ,(1997) , 10.1177/089270579701000503
Man Ken Cheung, David Chan, Mechanical and rheological properties of Poly(ethylene terephthalate)/polypropylene blends Polymer International. ,vol. 43, pp. 281- 287 ,(1997) , 10.1002/(SICI)1097-0126(199707)43:3<281::AID-PI800>3.0.CO;2-Q
M. N. Bureau, H. El Kadi, J. Denault, J. I. Dickson, Injection and compression molding of polystyrene/high‐density polyethylene blends—phase morphology and tensile behavior Polymer Engineering and Science. ,vol. 37, pp. 377- 390 ,(1997) , 10.1002/PEN.11680