Compound deep drawing and extrusion process for the manufacture of geared drum
作者： Xincun Zhuang , Xiaolong Sun , Hua Xiang , Min Xia , Zhen Zhao
DOI: 10.1007/S00170-015-7840-5
关键词:
摘要: A compound deep drawing and extrusion process was proposed in this study to produce the part like geared drum on a servo-controlled press. To improve formability of process, influences various slide motions speed motion, oscillation step material performance were studied based simple standard tensile test tests. And then, specific designed motion adopted evaluate their feasibility. The results showed that by setting at an early stage could not only achieve high surface quality but also reduce extent thickness reduction material.
springer.com
sci-hub.se 参考文章(14)
Dae-Hoon Ko, Sang-Kon Lee, Yong-Nam Kwon, Sang-Woo Kim, Bong-Hwan Kim, Byung-Min Kim, Dae-Cheol Ko, Improvement in dimensional accuracy of roll-die-formed clutch hub used in automotive transmission International Journal of Precision Engineering and Manufacturing. ,vol. 13, pp. 237- 243 ,(2012) , 10.1007/S12541-012-0029-Z
K. Mori, T. Maeno, Y. Fukui, Spline forming of ultra-high strength gear drum using resistance heating of side wall of cup CIRP Annals. ,vol. 60, pp. 299- 302 ,(2011) , 10.1016/J.CIRP.2011.03.144
Thomas Schneider, Marion Merklein, Sheet-Bulk Metal Forming of Preformed Sheet Metal Parts Key Engineering Materials. ,vol. 473, pp. 83- 90 ,(2011) , 10.4028/WWW.SCIENTIFIC.NET/KEM.473.83
H.-C. Wu, T. Altan, Process optimization in stamping—a case study for flanging a clutch hub from steel plate Journal of Materials Processing Technology. ,vol. 146, pp. 8- 19 ,(2004) , 10.1016/S0924-0136(03)00839-2
Jung Min Lee, Byung Min Kim, Chung Gil Kang, A study on the cold ironing process for the drum clutch with inner gear shapes International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 640- 650 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.07.027
P.B. Hussain, J.S. Cheon, D.Y. Kwak, S.Y. Kim, Y.T. Im, Simulation of clutch-hub forging process using CAMPform Journal of Materials Processing Technology. ,vol. 123, pp. 120- 132 ,(2002) , 10.1016/S0924-0136(02)00061-4
M. Merklein, J.M. Allwood, B.-A. Behrens, A. Brosius, H. Hagenah, K. Kuzman, K. Mori, A.E. Tekkaya, A. Weckenmann, Bulk forming of sheet metal CIRP Annals. ,vol. 61, pp. 725- 745 ,(2012) , 10.1016/J.CIRP.2012.05.007
Beyene Gezae Mebrahtu, Yu Jun Cai, Qiang Yu, Study on the Formability Rules with Precise Die Face for the Inner Clutch Shell of Automobile Advanced Materials Research. ,vol. 690-693, pp. 2923- 2927 ,(2013) , 10.4028/WWW.SCIENTIFIC.NET/AMR.690-693.2923
K. Osakada, K. Mori, T. Altan, P. Groche, Mechanical servo press technology for metal forming CIRP Annals. ,vol. 60, pp. 651- 672 ,(2011) , 10.1016/J.CIRP.2011.05.007
Qihang Wang, Lei Wang, Zhiwei Jiang, Shihua Gong, Algorithm for the generation of mandrel protection curve and trajectory scheme for spinning machine The International Journal of Advanced Manufacturing Technology. ,vol. 68, pp. 217- 226 ,(2013) , 10.1007/S00170-013-4722-6