The effect of sulfurization on the grinding wheel cutting ability in the internal cylindrical grinding of nickel superalloys
作者： Krzysztof Nadolny , Walery Sienicki , Michał Wojtewicz
关键词:
摘要: One possible way of preventing excessive growth smearings/loads on the grinding wheel active surface is introduction compounds such as sulfur, graphite, or wax into volume which exerts an influence adhesion during process impregnation. Limiting formation crucial importance to achieve effective hard-to-cut materials (such nickel superalloys) are characterized by considerable ductility and a strong chemical affinity abrasive grains, among other things. This article presents results experimental tests performed plunge sulfur impregnation wheels smearing/load intensity internal cylindrical openings made from Inconel® alloy 600 Incoloy® 800HT®. Bearing steel 100Cr6 was included in reference material. Grinding w...
sagepub.com
sci-hub.se 参考文章(20)
U. Teicher, A. Ghosh, A.B. Chattopadhyay, K. Künanz, On the grindability of Titanium alloy by brazed type monolayered superabrasive grinding wheels International Journal of Machine Tools & Manufacture. ,vol. 46, pp. 620- 622 ,(2006) , 10.1016/J.IJMACHTOOLS.2005.07.012
D. Herman, J. Markul, Influence of microstructures of binder and abrasive grain on selected operational properties of ceramic grinding wheels made of alumina International Journal of Machine Tools & Manufacture. ,vol. 44, pp. 511- 522 ,(2004) , 10.1016/J.IJMACHTOOLS.2003.10.026
Shuting Lei, Wenjie Liu, High-speed machining of titanium alloys using the driven rotary tool International Journal of Machine Tools & Manufacture. ,vol. 42, pp. 653- 661 ,(2002) , 10.1016/S0890-6955(02)00012-3
E.O. Ezugwu, Key improvements in the machining of difficult-to-cut aerospace superalloys International Journal of Machine Tools & Manufacture. ,vol. 45, pp. 1353- 1367 ,(2005) , 10.1016/J.IJMACHTOOLS.2005.02.003
W. Kapłonek, K. Nadolny, The Diagnostics of Abrasive Tools After Internal Cylindrical Grinding of Hard-to-Cut Materials by Means of a Laser Technique Using Imaging and Analysis of Scattered Light Arabian Journal for Science and Engineering. ,vol. 38, pp. 953- 970 ,(2013) , 10.1007/S13369-012-0374-3
G.S. Fox-Rabinovich, A.I. Kovalev, M.H. Aguirre, B.D. Beake, K. Yamamoto, S.C. Veldhuis, J.L. Endrino, D.L. Wainstein, A.Y. Rashkovskiy, Design and performance of AlTiN and TiAlCrN PVD coatings for machining of hard to cut materials Surface & Coatings Technology. ,vol. 204, pp. 489- 496 ,(2009) , 10.1016/J.SURFCOAT.2009.08.021
T M A Maksoud, A A Mokbel, J E Morgan, In-process detection of grinding wheel truing and dressing conditions using a flapper nozzle arrangement Proceedings of the Institution of Mechanical Engineers. Part B. Journal of engineering manufacture. ,vol. 211, pp. 335- 343 ,(1997) , 10.1243/0954405971516310
N Arunachalam, B Ramamoorthy, Texture analysis for grinding wheel wear assessment using machine vision Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture. ,vol. 221, pp. 419- 430 ,(2007) , 10.1243/09544054JEM577
D.A. Axinte, J. Kwong, M.C. Kong, Workpiece surface integrity of Ti-6-4 heat-resistant alloy when employing different polishing methods Journal of Materials Processing Technology. ,vol. 209, pp. 1843- 1852 ,(2009) , 10.1016/J.JMATPROTEC.2008.04.046
H.Z. Choi, S.W. Lee, H.D. Jeong, A comparison of the cooling effects of compressed cold air and coolant for cylindrical grinding with a CBN wheel Journal of Materials Processing Technology. ,vol. 111, pp. 265- 268 ,(2001) , 10.1016/S0924-0136(01)00531-3