Effect of surface textures on friction properties of Al2O3/TiC ceramics
作者： YQ Xing , JX Deng , YQ Tan , HM Zhou , None
DOI: 10.1179/1743294412Y.0000000031
关键词:
摘要: Regular surface textures with different geometrical characteristics were made on the of Al2O3/TiC ceramic tool materials by laser, and MoS2 solid lubricants subsequently filled into textured surfaces. Sliding wear tests carried out these ceramics. The friction coefficient was measured. features ceramics examined SEM. Results show that significantly reduced compared untextured one quite sensitive to texturing. wavy grooves its exhibited smallest among all samples tested. improvement in properties is attributed several physical mechanisms such as local increase lubricant supply reservoir creation formation thin lubricating film between sliding couples.
ingenta.com参考文章(30)
P P Shukla, J Lawrence, Modification of fracture toughness parameter K1c following CO2 laser surface treatment of Si3N4 engineering ceramic Surface Engineering. ,vol. 27, pp. 734- 741 ,(2011) , 10.1179/1743294411Y.0000000004
FY Sakata, AME Santo, W Miyakawa, R Riva, MSF Lima, None, Influence of laser surface texturing on surface microstructure and mechanical properties of adhesive joined steel sheets Surface Engineering. ,vol. 25, pp. 180- 186 ,(2009) , 10.1179/026708408X336364
L. Rapoport, A. Moshkovich, V. Perfilyev, I. Lapsker, G. Halperin, Y. Itovich, I. Etsion, Friction and wear of MoS2 films on laser textured steel surfaces Surface & Coatings Technology. ,vol. 202, pp. 3332- 3340 ,(2008) , 10.1016/J.SURFCOAT.2007.12.009
Min-soo Suh, Young-hun Chae, Seock-sam Kim, Tatsuya Hinoki, Akira Kohyama, Effect of geometrical parameters in micro-grooved crosshatch pattern under lubricated sliding friction Tribology International. ,vol. 43, pp. 1508- 1517 ,(2010) , 10.1016/J.TRIBOINT.2010.02.012
Deng Jianxin, Friction and wear behaviour of Al2O3/TiB2/SiCw ceramic composites at temperatures up to 800°C Ceramics International. ,vol. 27, pp. 135- 141 ,(2001) , 10.1016/S0272-8842(00)00052-3
H.L. Costa, I.M. Hutchings, Hydrodynamic lubrication of textured steel surfaces under reciprocating sliding conditions Tribology International. ,vol. 40, pp. 1227- 1238 ,(2007) , 10.1016/J.TRIBOINT.2007.01.014
A. Erdemir, Review of engineered tribological interfaces for improved boundary lubrication Tribology International. ,vol. 38, pp. 249- 256 ,(2005) , 10.1016/J.TRIBOINT.2004.08.008
P. Koshy, J. Tovey, Performance of electrical discharge textured cutting tools CIRP Annals. ,vol. 60, pp. 153- 156 ,(2011) , 10.1016/J.CIRP.2011.03.104
A. Moshkovith, V. Perfiliev, D. Gindin, N. Parkansky, R. Boxman, L. Rapoport, Surface texturing using pulsed air arc treatment Wear. ,vol. 263, pp. 1467- 1469 ,(2007) , 10.1016/J.WEAR.2006.11.043
O Verezub, Z Kálazi, G Buza, N V Verezub, G Kaptay, Classification of laser beam induced surface engineering technologies andin situsynthesis of steel matrix surface nanocomposites Surface Engineering. ,vol. 27, pp. 428- 435 ,(2011) , 10.1179/174329409X446296