摘要: AbstractA novel 12-station hip joint simulator with an anatomic position of the prosthesis was designed and built. The motion consists flexion-extension abduction-adduction. load is double-peak type. validation test done three similar 28 mm CoCr-polyethylene joints in diluted calf serum lubricant for 3.3 × 106 cycles. bearing surfaces polyethylene cups were burnished, CoCr heads undamaged, wear particles 0.1-1 μm size range, mean factor 5.7 10−7 mm3/N m. These essential observations good agreement clinical findings. In addition, 50 CoCR/CoCr joints, representing contemporary large-diameter metal-on-metal articulation tested. CoCr/CoCr calculated from Co Cr concentrations used quantified atomic absorption spectroscopy. jonits showed mild criss-cross...
sagepub.com
aalto.fi
sci-hub.se 参考文章(34)
RICHARD C. JOHNSTON, GARY L. SMIDT, Measurement of Hip-joint Motion during Walking: Evaluation Of An Electrogoniometric Method Journal of Bone and Joint Surgery, American Volume. ,vol. 51, pp. 1082- 1094 ,(1969) , 10.2106/00004623-196951060-00003
M.A. Wimmer, C. Sprecher, R. Hauert, G. Täger, A. Fischer, Tribochemical reaction on metal-on-metal hip joint bearings A comparison between in-vitro and in-vivo results Wear. ,vol. 255, pp. 1007- 1014 ,(2003) , 10.1016/S0043-1648(03)00127-3
J.R. Atkinson, D. Dowson, G.H. Isaac, B.M. Wroblewski, Laboratory wear tests and clinical observations of the penetration of femoral heads into acetabular cups in total replacement hip joints Wear. ,vol. 104, pp. 217- 224 ,(1985) , 10.1016/0043-1648(85)90049-3
WOLFRAM BRODNER, PETER BITZAN, VANEE MEISINGER, ALEXANDRA KAIDER, FLORIAN GOTTSAUNER-WOLF, RAINER KOTZ, Serum cobalt levels after metal-on-metal total hip arthroplasty. Journal of Bone and Joint Surgery, American Volume. ,vol. 85, pp. 2168- 2173 ,(2003) , 10.2106/00004623-200311000-00017
M. P. Kadaba, H. K. Ramakrishnan, M. E. Wootten, Measurement of lower extremity kinematics during level walking Journal of Orthopaedic Research. ,vol. 8, pp. 383- 392 ,(1990) , 10.1002/JOR.1100080310
D Dowson, B Jobbins, Design and development of a versatile hip joint simulator and a preliminary assessment of wear and creep in Charnley total replacement hip joints. Engineering in medicine. ,vol. 17, pp. 111- 117 ,(1988) , 10.1243/EMED_JOUR_1988_017_031_02
Vesa Saikko, Olof Calonius, Jaakko Ker�nen, Effect of counterface roughness on the wear of conventional and crosslinked ultrahigh molecular weight polyethylene studied with a multi-directional motion pin-on-disk device. Journal of Biomedical Materials Research. ,vol. 57, pp. 506- 512 ,(2001) , 10.1002/1097-4636(20011215)57:4<506::AID-JBM1196>3.0.CO;2-H
Kenneth R. St. John, Lyle D. Zardiackas, Robert A. Poggie, Wear evaluation of cobalt–chromium alloy for use in a metal‐on‐metal hip prosthesis Journal of Biomedical Materials Research Part B. ,vol. 68, pp. 1- 14 ,(2004) , 10.1002/JBM.B.10053
Vesa O Saikko, A three-axis hip joint simulator for wear and friction studies on total hip prostheses. Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine. ,vol. 210, pp. 175- 185 ,(1996) , 10.1243/PIME_PROC_1996_210_410_02
Harry McKellop, Sang-Hyun Park, Roberto Chiesa, Peter Doorn, Bin Lu, Patricia Normand, Peter Grigoris, Harlan Amstutz, In vivo wear of 3 types of metal on metal hip prostheses during 2 decades of use Clinical Orthopaedics and Related Research. ,vol. 329, ,(1996) , 10.1097/00003086-199608001-00013