Processing of T6 heat-treated Al-12Si-0.6Mg alloy
作者： Şenol Bayraktar , Onur Demir
DOI: 10.1080/10426914.2020.1732412
关键词:
摘要: In this study, ternary Al-12Si-0.6Mg material was manufactured by gravity die casting method in induction melting furnace. Microstructure images of alloy were taken on optical microscope after T6 h...
sci-hub.se 参考文章(37)
QG Wang, CJ Davidson, None, Solidification and precipitation behaviour of Al-Si-Mg casting alloys Journal of Materials Science. ,vol. 36, pp. 739- 750 ,(2001) , 10.1023/A:1004801327556
Mikell P. Groover, Fundamentals of modern manufacturing : materials, processes, and systems J. Wiley. ,(1996)
S. Bhowmick, A. Banerji, A.T. Alpas, Tribological behavior of Al–6.5%, –12%, –18.5% Si alloys during machining using CVD diamond and DLC coated tools Surface & Coatings Technology. ,vol. 284, pp. 353- 364 ,(2015) , 10.1016/J.SURFCOAT.2015.08.073
E. Samuel, A. M. Samuel, H. W. Doty, S. Valtierra, F. H. Samuel, Intermetallic phases in Al–Si based cast alloys: new perspective International Journal of Cast Metals Research. ,vol. 27, pp. 107- 114 ,(2014) , 10.1179/1743133613Y.0000000083
AE Markaki, TW Clyne, None, The effect of cell wall microstructure on the deformation and fracture of aluminium-based foams Acta Materialia. ,vol. 49, pp. 1677- 1686 ,(2001) , 10.1016/S1359-6454(01)00072-6
A. Gómez-Parra, M. Álvarez-Alcón, J. Salguero, M. Batista, M. Marcos, Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys Wear. ,vol. 302, pp. 1209- 1218 ,(2013) , 10.1016/J.WEAR.2012.12.001
M.S. Carrilero, R. Bienvenido, J.M. Sánchez, M. Álvarez, A. González, M. Marcos, A SEM and EDS insight into the BUL and BUE differences in the turning processes of AA2024 Al–Cu alloy International Journal of Machine Tools & Manufacture. ,vol. 42, pp. 215- 220 ,(2002) , 10.1016/S0890-6955(01)00112-2
D.K. Dwivedi, A. Sharma, T.V. Rajan, Machining of LM13 and LM28 cast aluminium alloys: Part I Journal of Materials Processing Technology. ,vol. 196, pp. 197- 204 ,(2008) , 10.1016/J.JMATPROTEC.2007.05.032
H.L Coldwell, R.C Dewes, D.K Aspinwall, N.M Renevier, D.G Teer, The use of soft/lubricating coatings when dry drilling BS L168 aluminium alloy Surface & Coatings Technology. ,vol. 177, pp. 716- 726 ,(2003) , 10.1016/J.SURFCOAT.2003.08.012
B. N. Pathak, K. L. Sahoo, Madhawanand Mishra, Effect of Machining Parameters on Cutting Forces and Surface Roughness in Al-(1-2) Fe-1V-1Si Alloys Materials and Manufacturing Processes. ,vol. 28, pp. 463- 469 ,(2013) , 10.1080/10426914.2013.763952